Humly comply with the needed certifications to operate in the markets that is targeted.
United States of America
FCC ID: 2APYB- HUM1001
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAUTION - Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.
This device is operation in 5.15 – 5.25GHz frequency range, then restricted in indoor use only. Outdoor operations in the 5.15 – 5.25GHz is prohibited.
This device is slave equipment, the device is not radar detection and not ad-hoc operation in the DFS band.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
European Union
European declaration of conformity
According to ISO / IEC Guide 22 and EN 450 14
Manufacturer’s Name: Certus Eiger Ltd.
Manufacturer’s Address: Unit 814, Houston Center, Mody Road, TST East Kowloon
Declares, under our sole responsibility that the product:
Product Name: Humly Room Display One
Model Number: HUM1001
Conforms to the following Product Specifications:
- RED 2014/53/EU LVD 2014//35/EU EMC 2014/53/EU RED
- EN 300 328
- EN 300 330
- EN 300 893
- EN 301 489-1
- EN 301 489-3
- EN 301 489-17
- EN 55032: 2015+AC: 2016
- EN 55035: 2017
- EN 62368-1: 2014+A11:2017
Supplementary information
In addition, the product is battery powered and the power supply provided with this product has been certified to IEC 62368-1: 2014. As manufacturer, we declare under our sole responsibility that the equipment follows the provisions of the Standards stated above.
Importer of Record
This Certus product has been tested and found to comply with all requirements for CE Marking and sale within the European Economic Area (EEA). The device has Bluetooth and wireless LAN approval and satisfies the requirements for Radio and Telecommunication Terminal Equipment specified by European Council Directive 2014/53/EU. These requirements provide reasonable protection against harmful interference when the equipment is operated appropriately in a residential or commercial environment.
CAUTION - Only approved accessories may be used with this equipment. In general, all cables must be high quality, shielded, correctly terminated and normally restricted to two meters in length. Power supplies approved for this product employ special provisions to avoid radio interference and should not be altered or substituted. Unapproved modifications or operations beyond or in conflict with these instructions for use may void authorization by the authorities to operate the equipment.
CE RF Power Table
|
Wifi 802.11b/g/n |
|||
|
CH |
b Freq(MHz) |
spec |
SISO Average(dBm) |
|
1 |
2412 |
17.5 |
15.10 |
|
7 |
2442 |
17.5 |
14.94 |
|
13 |
2472 |
17.5 |
15.09 |
|
CH |
g Freq(MHz) |
spec |
MIMO(A+B) Average(dBm) |
|
1 |
2412 |
17.5 |
17.18 |
|
7 |
2442 |
17.5 |
17.03 |
|
13 |
2472 |
17.5 |
17.17 |
|
CH |
n20 Freq(MHz) |
spec |
MIMO(A+B) Average(dBm) |
|
1 |
2412 |
17.5 |
17.05 |
|
7 |
2442 |
17.5 |
17.21 |
|
13 |
2472 |
17.5 |
17.00 |
|
Wifi 802.11ac |
|||
|
CH |
a Freq(MHz) |
spec |
MIMO(A+B) Average(dBm) |
|
36 |
5180 |
16.5 |
16.09 |
|
64 |
5320 |
16.5 |
15.45 |
|
100 |
5500 |
16.5 |
12.45 |
|
140 |
5700 |
16.5 |
12.64 |
|
CH |
n20 Freq(MHz) |
spec |
MIMO(A+B) Average(dBm) |
|
36 |
5180 |
16 |
15.31 |
|
64 |
5320 |
16 |
14.89 |
|
100 |
5500 |
16 |
12.97 |
|
140 |
5700 |
16 |
12.34 |
|
CH |
n40 Freq(MHz) |
spec |
MIMO(A+B) Average(dBm) |
|
38 |
5190 |
16 |
12.42 |
|
62 |
5310 |
16 |
14.33 |
|
102 |
5510 |
16 |
12.82 |
|
134 |
5670 |
16 |
15.85 |
|
CH |
ac80 Freq(MHz) |
spec |
MIMO(A+B) Average(dBm) |
|
42 |
5210 |
15 |
9.81 |
|
58 |
5290 |
15 |
12.44 |
|
106 |
5530 |
15 |
12.36 |
|
122 |
5610 |
15 |
14.75 |
|
BT |
||
|
CH |
Freq(MHz) |
Average(dBm) |
|
1M |
2402 |
1 |
|
2441 |
0.83 |
|
|
2480 |
0.04 |
|
|
CH |
Freq(MHz) |
Average(dBm) |
|
3M |
2402 |
1.14 |
|
2441 |
1.07 |
|
|
2480 |
0.25 |
|
|
BLE |
||
|
CH |
Freq(MHz) |
Average(dBm) |
|
1M |
2402 |
0.9 |
|
2440 |
0.73 |
|
|
2480 |
-0.07 |
|
|
CH |
Freq(MHz) |
Average(dBm) |
|
2M |
2402 |
0.83 |
|
2440 |
0.7 |
|
|
2480 |
-0.11 |
|